SHORVA...O explosion-proof boxes with window (flameproof joints) are applied for the arrangement of instruments, as well as any apparatuses for visual control, including monitors and displays in case of their mounting in hazardous areas, in harsh environments and for application is safe areas.
Casting technology used for the production of SHORVA...O explosion-proof boxes with window allows producing explosion-proof boxes with the highest strength characteristics, excluding formation of micro-cracks. Hence additional processing of internal surface of enclosure is not necessary, which enables to increase heat dissipated power of the enclosure.
SHORVA...-O explosion-proof enclosures with window are the fourth generation of enclosures with over 25 years of flameproof joint service life.
It is necessary to point out the possibility of application of these products by integrated equipment manufacturers, where superior quality of mechanical processing of aluminum is put to the forefront.
Full production cycle from foundry patterns to finished products is carried out by explosion-proof equipment plant “ZAVOD GORELTEX” Co. Ltd. (former “CORTEM-GORELTEX” Co. Ltd) in the territory of the Russian Federation.
Scope of application – underground mines and pits hazardous with gas (methane), coal dust; outdoor and indoor hazardous areas as per explosion protection marking, GOST 30852.13-2002 (IEC 60079-14:1996), areas with presence of combustible dust, as per GOST IEC 61241-3-2011, dangerous production facilities of I, II, III, IV hazard class supervised by Rostechnadzor of the RF and national technical supervision bodies of the Customs Union and CIS countries.
|Box dimension type||Dimensions, mm||Mass, kg|
|Name*||Dimensions, mm||Mass, kg|
Note: bus bars having 2 holes x 16 mm2 and a row of holes 6 mm2 (number depends on the bus bar length) are installed by default for options /SHINA G and /SHINA N. Installation of bus bars with another diameter of holes is possible upon customer‘s approval.
|SHORVA||Х||-O||Х||-||Х||Х||(||Х||) -||Х||Х||(||Х||) /||Х||– TU 3400-005-72453807-07|
|Enclosure size code|
|Window size code|
|Number of cable glands|
|Cable gland type|
|Side of cable gland location|
|Options, accessories and versions|
IIGb / IIIDb EXPLOSION-PROOF FRAMES FOR MODULAR VERSION
When designing cabinets there are situations where dimensions of enclosures are not sufficient to arrange the equipment. In this case the cabinet may be divided into separate modules connected either by metal hoses or by pipe conduit. Application of relatively small modules enables to reduce the dimensions, mass and cost of the cabinet.
Moreover, large surface areas enable to arrange cable glands in accessible places which significantly simplifies the mounting. Modular cabinets are installed on the frame /RAMA made from galvanized steel (cold or hot-dip galvanizing) or stainless steel upon request.
Frames are manufactured for wall or floor mounting and are frictionally intrinsically safe non-electrical equipment with IIGb and IIIDb level of explosion protection.
MECHANICAL PROCESSING OF SHORVA...-O BOXES
Wall and cover thickness of SHORVA...-O explosion-proof enclosures is sufficient to manufacture threaded holes for connection of various types of explosion-proof cable glands, control and indicating elements. There is a wide range of control, indicating and signaling elements of standard version, elements and modules for specific tasks, as well as elements of typical version upon customer’s request. Big size of control elements of M series enables to work in gloves, indicating elements have large diameter – 40 mm and are equipped with a reflector which makes the signal clearly visible at large viewing angle and various degrees of surface dirtiness. Operating handles for circuit breakers are selected depending on number of poles and circuit breaker type. Handle’s axle length can be adapted to the type of circuit breaker and size and type of the explosion-proof enclosure.
|Box dimension type||On one side|
|Type of thread of cable gland|
ARRANGEMENT OF EQUIPMENT INSIDE SHORVA...-O BOXES
Typical electrical components installed in boxes: I&C, as well as other apparatuses for visual control, including monitors and displays, video cameras, IT components, relays and timers, terminals, fuses, etc. Electrical equipment and components supplied with boxes are produced by leading manufacturers. In case you need any specific components, please, provide respective specification when ordering. The above list of electrical equipment and components is not exhaustive. Other versions of equipment may be supplied upon special order.
|Previous international name
"ZAVOD GORELTEX" Co. Ltd.
(former "CORTEM-GORELTEX" Co. Ltd.)
|The Customs Union name
"ZAVOD GORELTEX" Co. Ltd. (former "CORTEM-GORELTEX" Co. Ltd.)TU 3400-005-72453807-07